Nossos Produtos RFID
-
Linha de Imprensa Fin
-
Morrer de barbatana
-
Ferramentas manuais
-
Peças de Reposição
-
Óleo evaporativo para prensa de aletas e dobra de tubo
-
Expansor de tubo para trocador de calor
-
Máquina de inserção automática de tubos com aletas
-
Dobrador de tubo para trocador de calor
-
Forno de Brasagem de Alta Temperatura
-
Máquina de fabricação do evaporador do refrigerador
-
Máquina de Forno Trocador de Calor
-
Máquina de Brasagem
-
Máquina de tubo de cobre de isolamento
-
Máquina de fabricação de acessórios de cobre
-
Máquina de dobrar bobinas
-
Máquina de dobra de retorno
-
Máquina de Flange de Punção de Tubos
-
Máquina de limpeza de dobrador de retorno
-
Máquina de bobina de panqueca
-
Máquina de corte do tubo
-
Máquina de perfuração de furo de tubo
-
Máquina de colarinho pequeno do tubo
-
Máquina integrada de tubos
-
Máquina de fechamento de tubos
-
Máquina de inserção de anel
-
Máquina de dobra de borda da placa do refrigerador de ar
-
Tubo de cobre e máquina de fusão de tubo de alumínio
-
Máquina de dobra de tubos
-
Máquina formadora de extremidades de tubos
-
Equipamento de teste de vazamento de hélio
-
Máquina de fabricação de anel de solda
-
Máquina de dobra de tubo serpentina
-
Máquina de fiação
Máquina de dobra de serpentina de tubo
Máquina de dobra automática completa do tubo de alumínio do refrigeradorFunção do equipamento: 1. A máquina é de uma em cada dez estruturas, ou seja, dobrando dez tubos ao mesmo tempo.
2. Toda a máquina adota servo drive, acionamento hidráulico e acionamento pneumático.
3. O sistema de controle elétrico é controlado por PLC + tela sensível ao toque. PLC adota a marca Mitsubishi, tela sensível ao toque adota Taiwan Weilun marca, e aparelhos elétricos de baixa tensão adota marca Schneider. Princípio de funcionamento:
1. The pipe bender is mainly composed of discharging device, straightening device, primary feeding device, cutting device, secondary feeding device, bending device, table rotating device, rack and electric control device. The whole action is driven by oil cylinder and servo motor, and the electric appliance is controlled by PLC + touch screen. The pipe bender is developed by imitating the imported automatic pipe bender. The action steps and technological process are completely the same as those of the imported equipment, which is relatively reasonable.
2.Put the whole coil into the discharging rack, and lead the pipe end to the feeding clamp of primary feeding. Press the start button, the primary feeding device will send the pipe through the cutting device to the secondary feeding clamp. At this time, the primary feeding clamp returns to its original position, stops working, the secondary feeding clamp starts working, and the pipe is sent into the bending wheel to start bending. When bending to a certain length, cut off the pipe and continue bending until the final bending is completed, and take out the bent single piece manually. Press the start button again, the machine will repeat the above feeding elbow action, so as to cycle.
1. The pipe bender is mainly composed of discharging device, straightening device, primary feeding device, cutting device, secondary feeding device, bending device, table rotating device, rack and electric control device. The whole action is driven by oil cylinder and servo motor, and the electric appliance is controlled by PLC + touch screen. The pipe bender is developed by imitating the imported automatic pipe bender. The action steps and technological process are completely the same as those of the imported equipment, which is relatively reasonable.
2.Put the whole coil into the discharging rack, and lead the pipe end to the feeding clamp of primary feeding. Press the start button, the primary feeding device will send the pipe through the cutting device to the secondary feeding clamp. At this time, the primary feeding clamp returns to its original position, stops working, the secondary feeding clamp starts working, and the pipe is sent into the bending wheel to start bending. When bending to a certain length, cut off the pipe and continue bending until the final bending is completed, and take out the bent single piece manually. Press the start button again, the machine will repeat the above feeding elbow action, so as to cycle.
RETA MÁQUINA CO., LTD
Adicionar: No.2 Xinghengyizhi Road, Cicheng Industry Park, Jiangbei District, 315000, Ningbo City, Zhejiang Province, China
Telefone: : +86-574-81106661
E-mail: info@retamachine.com
Web :www.retamachine.com
Pesquisa Relacionada
- Máquina de dobra de serpentina de tubo
Anterior Cortador de aletas